GE DISHWASHER FINE FILTER ASSEMBLY – WD12X10109

Fine filter assembly works with some GE, and Hotpoint models of dishwashers. How to Replace the WD12X10109 GE Dishwasher Fine Filter Assembly

Replacing the WD12X10109 GE dishwasher fine filter assembly is a relatively simple DIY project that can be completed quickly with few tools and basic technical skills. This guide will walk you through step-by-step instructions on how to perform this task in a safe and effective manner.

Step 1: Going Prepare the Dishwasher

Prior to disassembling your dishwasher, you should make sure that all power has been turned off. Unplug the electrical cord from the wall outlet and turn off the circuit breaker that controls the dishwasher.

Once the power has been turned off, open the door of the dishwasher and remove any dishes or utensils that are stored inside.

Step 2: Removing the Filter

The filter assembly is located in the lower portion of the dishwasher tub. To access the filter assembly, you will need to locate the screws that secure the bottom panel of the dishwasher to the sides of the tub. Using a Phillips-head screwdriver, loosen and remove the screws that are securing the bottom panel.

Once the screws have been removed, the bottom panel of the dishwasher can be carefully pulled away from the sides of the tub. Locate the filter assembly which is typically near the center of the opening.

Using a pair of pliers, loosen the mounting screws that secure the filter to the dishwasher frame and carefully pull out the filter assembly.

Step 3: Cleaning the Dishwasher Tub
vacuuming the interior surface of the dishwasher tub. This will ensure that any food particles or dirt that has accumulated in the tub is removed.

Step 4: Replacing the Filter Assembly

Carefully lift the new filter assembly into place in the dishwasher and tighten the mounting screws to secure it in place.

Replace the bottom panel of the dishwasher and secure it to the sides of the tub with the screws removed earlier.

Step 5: Testing the Dishwasher

Plug the electrical cord back into the wall outlet and turn the circuit breaker back on. Close the door of the dishwasher and start a short cycle to test that the filter assembly has been correctly replaced.

Once the short cycle has completed, open the door and inspect the interior of the dishwasher to ensure that the filter has been correctly installed and that the dishwasher is functioning properly.

Conclusion

Replacing the WD12X10109 GE dishwasher fine filter assembly is a straightforward and cost efficient DIY project that can be completed quickly with minimal effort. By following the steps outlined in this guide, you will be able to replace your filter assembly safely and efficiently.

Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer’s manual, if available. Search CDW9380N00SS CDW9380N20SS CDWT280V00SS CDWT280V05SS CDWT280V50SS CDWT980R10SS CDWT980R30SS CDWT980V05SS CDWT980V50SS EDWF800P00BB EDWF800P00WW EDWF860P00SS GDWF100R10BB GDWF100R10WW GDWF100V40BB GDWF100V40WW GDWF100V50BB GDWF100V50WW GDWF100V55BB GDWF100V55WW GDWF150V40ES GDWF150V50ES GDWF150V55ES GDWF160R10SS GDWF160R30SS GDWF160V00SS GDWF160V40SS GDWF160V50SS GDWF160V55SS GDWT100R00BB GDWT100R00WW GDWT100R05BB GDWT100R05WW GDWT100R10BB GDWT100R10WW GDWT100R30BB GDWT100R30WW GDWT160R00SS GDWT160R05SS GDWT160R10SS 1 2 3 4 5