SPEED QUEEN WASHER AGITATE AND SPIN BELT – 38174

The 38174 Speed Queen / Alliance Washer Agitate and Spin Belt is perfect for your Speed Queen / Alliance washer. This belt is made of high-quality rubber and designed to keep your washer running smoothly and efficiently, agitating and spinning the clothes during the wash cycle. The belt has a width of ¾” and lasts up to 10 years to help reduce wear and tear on your washer. This belt is easy to install and comes with instructions for hassle-free installation. This belt will give you years of reliable service, perfect for keeping your washer working like new. We’re your #1 source for genuine OEM appliance parts. Contact us for further questions as well as any other appliance parts needs! Step 1: Unplug the Washer

Before beginning any repairs, it is important to turn off and unplug the washer from the wall outlet. Also, shut off the water supply valves to the washer.

Step 2: Remove the Top Panel and Agitator

To gain access to the agitate and spin belt, the top panel of the washer must be removed. Begin by removing the screws located on the sides of the panel, then gently lift the panel off. The agitator can then be removed by removing the bolt located at the center of the agitator and lifting the unit up.

Step 3: Loosen the Motor Mounting Bolts

Located on the sides of the motor are two mounting bolts. Use a wrench to loosen and remove these bolts. The motor can then be pulled away from the base of the washer.

Step 4: Disconnect Belt from Motor

Locate the belt that is connected between the motor and the agitate and spin pulley. Loosen the belt and remove it from both the motor and the pulley.

Step 5: Install New Belt

Once the old belt has been removed, install the new belt onto the motor and the pulley. Make sure the belt is routed correctly and is properly tightened.

Step 6: Reinstall Motor

Reinstall the motor into the washer with the two mounting bolts. Be sure the bolts are tightened securely.

Step 7: Reinstall Agitator

Replace the agitator back into the washer, making sure that the bolt at the center is tightened properly.

Step 8: Reinstall Top Panel

Once the agitator is in place, the top panel of the washer can be replaced. Secure the top panel with screws and ensure the door latches are lined up correctly.

Step 9: Plug in Washer and Re-attach Water Supply Lines

Now that all repairs have been completed, the washer can be re-plugged in and the water supply lines can be re-attached.

Step 10: Test Washer

Finally, test the washer to make sure the agitate and spin belt replacement was successful. Fill the washer with a small load of laundry and run the cycle to check for proper operation.

Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer’s manual, if available. Search AWN311SP111TW01 AWN402PP111TW01 AWN412SP111TW01 AWN432SP111TW01 AWN432SP113CW04 AWN432SP113FW28 AWN432SP113TW01 AWN432SP113TW04 AWN542SP111TW01 AWN542SP111TWAH AWNE82SP113CW01 AWNE82SP113FW01 AWNE82SP113TW01 AWNE92SP113FW01 AWNE92SP113TW01 AWNE92SP123DW01 AWNE92SP543DW01 AWS01NW AWS17NW AWS44NW AWS45NW AWS48NW AWS51NW AWS52NW AWS53NW AWS75NW AWS76NW AWZ17N*-1102 AWZ44N*-1102 AWZ45N*-1102 AWZ51N*-1102 AWZ52N*-1102 AWZ53N*-1102 CWN311SP111CW01 CWN412SP111CW01 DWN412SP111CW01 DWN432SP113CW01 DWN432SP113CW04 LWB19B*-1109 LWB19M*-1109 1 2 3 4