WHIRLPOOL TERMINAL BLOCK SCREW AND NUT KIT – 279393

This Whirlpool Terminal Block Screw and Nut Kit comes with all the hardware you need to replace the terminals on your range or dryer. This kit includes four screws and four nuts in a zinc finish that provide superior corrosion resistance. It’s easy to install, so it will be a perfect replacement part if your terminals start to fail. Plus, it’s backed by a 1-year warranty for quality assurance. This kit is ideal for helping to get your dryer or range set up and running quickly and safely. We’re your #1 source for genuine OEM appliance parts. Contact us for further questions as well as any other appliance parts needs! Step #1: Gather the proper tools. For replacing a 279393 Whirlpool Terminal Block Screw and Nut Kit, you will need the following: a flat-head screwdriver; a Phillips-head screwdriver; a pair of needle nose pliers; and the replacement 279393 Whirlpool Terminal Block Screw and Nut Kit.

Step #2: Turn off power to the appliance. Before starting any repair work on an appliance, turn off the power. On most appliances this can be done by flipping the switch on the wall.

Step #3: Open the appliance. Depending on the model of your appliance, you may need to remove the screws from the top or side panels and lift them away. Be sure to place the screws in a safe place so that you don’t lose them.

Step #4: Locate the terminal block. The terminal block is typically located near the back of the appliance and is where the wiring connects to the appliance. It should be clearly visible and labeled.

Step #5: Disconnect the wires. Once you have located the terminal block, use the needle nose pliers to carefully disconnect the wires. If the terminals are stuck, you may need to use the flat-head screwdriver to help loosen them.

Step #6: Remove the old screw & nut kit. Once the wires are disconnected, use the Phillips-head screwdriver to remove the screws and nut kit from the terminal block.

Step #7: Install the new screw & nut kit. Once all the old parts have been removed, install the new 279393 Whirlpool Terminal Block Screw and Nut Kit into the terminal block. Make sure that each piece is securely fastened in place.

Step #8: Reconnect the wires. Finally, use the needle nose pliers to reconnect the wires to the terminal block.

Step #9: Test the appliance. Once everything has been installed and reconnected, turn the power back on and test the appliance to make sure everything is functioning properly.

Step #10: Replace the side/top panels. Once you are sure that the appliance is working properly, replace the side or top panels and secure them with the screws that were removed in Step 3.

Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer’s manual, if available. Search 1CWED4800DQ0 1CWED4900DW0 1CWED5100VQ0 1CWED5100VQ1 1CWED5200VQ0 1CWED5200VQ1 1CWED5300VW0 1CWED5700VW0 1LE4930XKW0 1LE5700XKW0 1LE5920XKW0 1LE7800XKW0 1MWED1750EM0 3CE2110XMW0 3CE2110XMW1 3CE2110XMW2 3CE2910XSN0 3CE2910XSN1 3CE2910XSW0 3CE2910XSW1 3CEP2910BW0 3CEP2910DW0 3CEP2920DW0 3CEP2950DN0 3CEP2950DW0 3CEP2960DN0 3CEP2960DN2 3CEP2960DW0 3CEP2960DW2 3CFE2510W1 3CFE2510W2 3CGP2951DW1 3CSP2760BN0 3CSP2760BW0 3DWED4800YQ0 3DWED4800YQ1 3DWED4800YQ2 3DWED4900YW0 3DWED4900YW1 3DWED4900YW2 1 2 3 4 5