GE General Electric Hotpoint Sears Kenmore Range Oven Igniter Assembly WB13T10045We are a Factory Authorized Parts Distributor for General Electric Hotpoint. Trust us for all of your General Electric Hotpoint appliance parts and accessories needs. Replacing the WB13T10045 GE Oven Ignitor Assembly: A Step-by-Step DIY Guide <\/p>\n
Are you experiencing problems or faults with your GE oven\u2019s ignitor assembly? Then it\u2019s time for a DIY replacement! Replacing the faulty WB13T10045 GE oven ignitor assembly is relatively simple and straightforward, requiring only a few basic tools. The following guide will show you how to replace the WB13T10045 GE oven ignitor assembly in 8 easy steps: <\/p>\n
Step 1: Unplug the oven
Before performing any maintenance, it is essential to unplug the oven. This will prevent any electrical shock during the replacement process. <\/p>\n
Step 2: Remove the oven door
Locate the two door hinges on the outside of the oven and use a Phillips screwdriver to remove the screws holding the door in place. Once the screws have been removed, lift the door off the stove top. <\/p>\n
Step 3: Remove the oven bottom panel
Look for the four screws on the inside of the oven that hold the bottom panel in place. Unscrew the screws to remove the panel. <\/p>\n
Step 4: Remove the old ignitor assembly
Locate the old ignitor assembly and unscrew it from the burner tube. Disconnect the wires from the old assembly and remove it from the oven. <\/p>\n
Step 5: Install the new ignitor assembly
Take out the new ignitor assembly from its package and carefully insert it into the burner tube. Secure it by screwing it into place. <\/p>\n
Step 6: Connect the new ignitor wires
Connect the wires from the new ignitor assembly to the existing wiring. Make sure the connections are secure and properly insulated. <\/p>\n
Step 7: Reinstall the bottom panel
Replace the bottom panel and reinsert the four screws. <\/p>\n
Step 8: Reattach the oven door
Lay the oven door on the stove top and reattach it to the hinges using the Phillips screws. Plug the oven back in and you\u2019re done! <\/p>\n
By following these simple steps, you should have replaced the WB13T10045 GE oven ignitor assembly in no time. If you encounter any issues during the process, be sure to refer to the manufacturer\u2019s instructions.<\/p>\n
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer’s manual, if available. Search JGS905BEK1BB JGS905BEK2BB JGS905BEK3BB JGS905KEK1CC JGS905KEK2CC JGS905KEK3CC JGS905TEK1WW JGS905TEK2WW JGS905TEK3WW JGS968BEK1BB JGS968BEK2BB JGS968BEK3BB JGS968BEK4BB JGS968BH1BB JGS968BH2BB JGS968BH3BB JGS968BH4BB JGS968BH5BB JGS968BH6BB JGS968KEK1CC JGS968KEK2CC JGS968KEK3CC JGS968KEK4CC JGS968KH1CC JGS968KH2CC JGS968KH3CC JGS968KH4CC JGS968KH5CC JGS968KH6CC JGS968SEK1SS JGS968SEK2SS JGS968SEK3SS JGS968SEK4SS JGS968TEK1WW JGS968TEK2WW JGS968TEK3WW JGS968TEK4WW JGS968TH1WW JGS968TH2WW JGS968TH3WW 1 2 3 4 5<\/p>\n","protected":false},"excerpt":{"rendered":"